Wave PTMP/PTP 4.1.1 includes the below improvements and fixes.

Improvements

• Improved main radio beamforming and performance.
• Improved 60 GHz PTMP link performance by resolving RX reordering limitations when multiple stations are connected.
• Improved 60 GHz dynamic distance updates.
• Improved backup radio multicast throughput.
• Improved backup radio automatic channel selection.
• Improved DHCP Option 82 support for MGMT VLAN and Data VLAN configurations.
• Added support for custom Remote ID configuration in DHCP Option 82.
• Added historical data with adjustable time frames to the capacity and throughput chart.
• Added support for 31-bit LAN netmask in router mode when DHCP server is disabled.
• Added read-only user support.
• Improved system stability, including router mode stability under specific traffic conditions.
• System security updates.

Bugfixes

• Fixed an issue affecting main radio transmission when multiple stations reconnect.
• Fixed an issue where the 60 GHz radio could stop passing traffic in some scenarios.
• Fixed a rare issue where the 60 GHz radio could experience a kernel module crash.
• Fixed an issue where 60 GHz auto-rate could get stuck at low modulation levels and not recover after link conditions improved.
• Fixed a rare case where a 60 GHz station remained stuck in a connecting/authenticated state after an AP firmware reset.
• Fixed an issue where IPv6 RS/RA packets did not pass through the Wave link.
• Fixed a potential MAC address conflict in router mode with MGMT VLAN enabled.
• Fixed a rare router mode crash under certain UDP traffic patterns.
• Various UX fixes.

Additional information

• DHCP Option 82 Remote ID format was changed to the MAC binary format.

Wave PTMP/PTP 4.1.0 includes the below improvements and fixes.

Improvements

• Introducing Link Assistant - warning and informational messages, along with resolution tips, are now centralized in the Alerts menu.
• Improved backup radio performance and resiliency in noisy environments.
• Improved main radio airtime distribution bar, now displaying interference and available in both Access Point and Station modes.
• Improved main radio performance for long distance links.
• Improved beamforming for the 60 GHz radio.
• Aligned main radio regulatory requirements for Israel.
• Updated Dashboard and Tools design and layout for improved usability.
• Added real-time channel utilization bar for backup radio.
• Added Web UI light/dark mode.
• Added Lock to AP feature.
• Added DMZ support in router mode.
• Added Firewall support in router mode.
• Added static routes support in router mode.
• Added an option to disable NAT in router mode.
• Added Ethernet port details tooltip to the Dashboard.
• Added various UX improvements to the Dashboard.
• System security updates.
• Added SNMP MIB object 'af60StaDxCapacity' for wireless capacity reporting.
• Added SNMP MIB object 'af60StaFrequency' for remote peer active radio frequency reporting.
• Added SNMP MIB object 'af60StaBandwidth' for remote peer active radio bandwidth reporting.

Bugfixes

• Fixed main radio signal degradation over time.
• Fixed rare condition preventing failover from backup to main radio.
• Wave Pro: Fixed carrier drop not disabling the SFP+ port.
• Fixed an occasional 60 GHz performance drop after reconnect.
• Fixed an issue where enabling Wave AI forced the 5 GHz frequency setting to Auto.
• Fixed backup radio wireless QoS operation.
• Added a fix to prevent third-party devices from associating with the Wave AP.
• Fixed DHCP Option 82 Circuit ID and Remote ID duplication issue.
• Fixed SNMP MIB object 'af60StaRemoteConnectionTime' reporting invalid connection time.
• Fixed SNMP failures on peer statistics timeout events.
• Fixed SNMP memory usage.
• Web UI: Fixed an issue where DHCP settings could be disabled when modifying other settings.
• Added various UX and system stability fixes.

Additional information

SNMP MIBs have been updated. Please import the new MIB files from the included ZIP. Users who updated the SNMP MIBs during 4.1.0-RC should update them again.

Wave PTMP/PTP 4.1.0-RC4 includes the below improvements and fixes.

Improvements

• Improved beamforming for 60 GHz radio.

Bugfixes

• Fixed an occasional 60 GHz performance drop after reconnect.

Wave PTMP/PTP 4.1.0-RC3 includes the below improvements and fixes.

Improvements

• Improved main radio performance for long distance links.
• Aligned main radio regulatory requirements for Israel.

Bugfixes

• Fixed SNMP memory usage.
• WEB UI: Various fixes.

Wave PTMP/PTP 4.1.0-RC2 includes the below improvements and fixes.

Improvements

• Web UI: UX improvements for Dashboard.

Bugfixes

• Fixed an issue where the 60 GHz radio would stop passing traffic after reconnecting.
• Fixed an issue where enabling Wave AI forced the 5 GHz frequency setting to Auto.
• Web UI: Fixed an issue where DHCP settings could be disabled when modifying other settings.

Wave PTMP/PTP 4.1.0-RC includes the below improvements and fixes.

Improvements

• Added SNMP MIB object 'af60StaDxCapacity' for wireless capacity reporting.
• Added SNMP MIB object 'af60StaFrequency' for remote peer active radio frequency reporting.
• Added SNMP MIB object 'af60StaBandwidth' for remote peer active radio bandwidth reporting.
• Added Ethernet port details tooltip to the Dashboard.

Bugfixes

• Fixed DHCP Option 82 Circuit ID and Remote ID duplication issue.
• Fixed SNMP MIB object 'af60StaRemoteConnectionTime' reporting invalid connection time.
• Fixed SNMP failures on peer statistics timeout events.
• Added various UX and system stability fixes.

Additional information

SNMP MIBs have been updated. Please import the new MIB files from the included ZIP.

Wave PTMP/PTP 4.0.1 includes the below improvements and fixes.

Improvements

• Improved main radio stability.

Bugfixes

• Fixed an issue preventing password change via the WebUI.
• Fixed system stability issues during support file generation.
• Fixed backup radio site surveys failing on stations not associated with an AP.
• Fixed link detection issues with certain SFP+ modules.
• Fixed DHCP leases not reaching LAN clients in router mode when Block Management is enabled.
• Fixed traffic pass-through issues when operating on the backup radio with Data VLAN enabled.
• Fixed device orientation not displaying in the alignment tool when no link is present.
• Fixed Privacy Policy/EULA/ToS links that did not open when accessed via UISP remote web access.

Wave PTMP/PTP 4.0.0 includes the below improvements and fixes.

Improvements

• Major system update bringing core enhancements, along with improvements to the backup radio for better stability, performance, and lower latency.
• Improved main radio stability, latency, and co-location performance.
• System security updates.
• Improved backup radio automatic channel selection.
• Improved antenna alignment tool design.
• Improved urescue mode reliability.
• Improved system watchdog for more reliable fault handling.
• Aligned main radio regulatory requirements for Italy.
• Aligned backup radio regulatory requirements for Australia, Brazil, Canada, Kazakhstan, Japan, and the United Kingdom.
• Added DHCP Option 82 support.
• Added MAC ACL feature to PtMP/PtP AP mode.
• Added rate limiting for failed login attempts.
• Added Ethernet port management feature for router mode.
• Added operating frequency marking to the site survey tool.
• Added UISP remote access support for the local web interface. Requires UISP Application 2.4.143 or newer.

Bugfixes

• Fixed main radio assert triggered by receiving a jumbo frame.
• Fixed issue causing excessive ARP requests in router mode.
• Fixed brief inaccuracies in backup radio signal reporting during initial station connection.
• Fixed a rare issue causing statistics to become unresponsive.
• Fixed unintended ARP responses from virtual interfaces.
• Fixed failover slider not applying when the main radio is disconnected.
• Fixed issue where the domain search list from DHCP was not applied correctly.
• Fixed IPv6 RS packets not passing in PtMP mode with Multicast Enhancement enabled.
• Fixed negative temperature reporting for SFP+ modules.
• Fixed device not responding to discovery requests in urescue mode.
• Fixed alignment tool sector layout on mobile devices.
• Wave Pro: Fixed a potential loop issue in router mode.
• Added various UX, system reporting, and stability fixes.

Additional information

DHCP Option 82 is available on supported hardware in PtMP bridge mode.

Wave PTMP/PTP 3.4.4 includes Wave AP Gen2 support.

Improvements

• Added support for Wave AP Gen2.

Wave PTMP/PTP 3.4.0 includes the below improvements and fixes.

Improvements

• Increased PtMP client capacity from 24 to 31.
• Improved main radio latency, performance, and stability.
• Added an option to disable the backup radio for stations in PtMP mode.
• Added traffic shaping support to PtMP/PtP station mode.
• Aligned main radio regulatory requirements for the Philippines.
• Improved backup configuration loading with options to apply changes immediately or test changes.
• Improved the Ethernet cable test with additional display options.
• Added more configurable options to disable LAN or WAN management access in Router mode.
• Improved UX for regulatory information.
• Wave AP Micro: Improved beam-forming for newly associated stations.

Bugfixes

• Fixed backup radio signal reporting on high-frequency channels.
• Fixed site survey report issues for SSIDs with special characters.
• Fixed inaccessible IPv6 link-local address in router mode with MGMT VLAN.
• Added a fix for configuration file upload on the initial login page.
• Added various UX, system reporting, and stability fixes.
• Wave Pro: Fixed SNMP not working in router mode with MGMT VLAN enabled.

Additional information

Traffic shaping is available on supported hardware in PtMP/PtP station mode.

Wave PTMP/PTP 3.3.1 includes the below improvements and fixes.

Improvements

• Improved main radio performance for long distance links and high client count.
• Improved backup radio stability.
• Improved mobile view in the WebUI with enhanced tool layouts and a newly implemented side menu.
• Added a configurable failover threshold setting.
• Added channel utilization bar to the backup radio site survey tool.
• Added sector view description and tips for antenna alignment.

Bugfixes

• Fixed system configuration issue when changing PtP Main mode.
• Fixed SNMP SFP+ speed reporting.
• Fixed Data VLAN configuration issues.
• Added a fix for IPv6 RA not passing in PtP mode.
• Added a fix for the 5GHz site survey displaying an incorrect neighbor operating frequency.
• Added ping watchdog support info collection fix.
• Added various UX, system reporting, and stability fixes.

Wave PTMP/PTP 3.3.0 includes these improvements.

Improvements

• Increased supported client capacity from 15 to 24.
• Added 540 MHz channel width support for better 60 GHz link resiliency.
• Added main radio GPS synchronization for PtP/PtMP AP mode.
• Added backup radio automatic channel selection.
• Added site survey tool.
• Added SFP+ port diagnostic tool alongside improved RJ45 cable test.
• Added Ethernet port management.
• Aligned main radio regulatory requirements for Australia, India, Indonesia, Mexico, New Zealand, Singapore, South Africa, Taiwan, and the United States.
• Improved main radio connection stability, latency, and performance.
• Improved main radio rate algorithm.
• Improved failover switching between the main and backup radio.
• Improved SFP+ port stability.
• Improved backup configuration loading - configuration can be reviewed and applied without the need for a reboot.
• Improved device boot sequence resiliency.
• Improved antenna alignment tool.
• Improved mobile view of user interface.
• System security updates.

Bugfixes

• Added wireless QoS fix.
• Added SNMP community field fix.
• Added STP loop issue fix.
• Added Wave AI peer connection tracking fix.
• Added various system settings, reporting, and stability fixes.
• Added various UX fixes.

Additional information

• GPS synchronization is available on supported hardware configurations in PtP/PtMP AP mode.

Wave PTMP/PTP 3.2.2 includes Wave Pico support.

Improvements

• Added support for Wave Pico.

Wave PTMP/PTP 3.2.0 includes the below bugfixes and improvements.

Improvements

• Added PTP/PTMP mode switching for Wave Nano, Wave LR and AF60-LR.
• Added PTMP AP airtime distribution bar for main radio.
• Added MCS 12 support for main radio.
• Added Wave PRO support.
• Improved main radio connection stability, performance and latency.
• Improved expected signal estimation.
• Improved stability of PTMP AP connection with high CPE count.
• Improved backup radio connection stability, performance and latency.
• Improved failover switching between the main and backup radio.
• Improved backup radio's received signal reporting.
• Improved multicast enhancement performance.
• Improved router mode performance.
• Improved backup radio's regulatory rules for Australia, Brazil, Canada, Chile, Czech Republic, Egypt, India, New Zealand, United States and Japan.
• Added option for turning backup radio on/off for PTP mode
• Added data VLAN support.
• Added ARP table, Bridge table and Routes information in Dashboard Network section.
• Added ability to select a main or backup radio to test when using speed test.
• Added user interface redirect, when static IP address is changed.
• Added Ubiquiti SSO support for devices managed by UISP application.
• Added port forwarding capability.
• Changed naming convention where AP-Tx (CPE-Rx) is Downlink and CPE-Tx (AP-Rx) is Uplink.
• Added various system settings, reporting and stability fixes.
• Added various UX improvements.

Bugfixes

• Fixed Tx power setting for backup radio.
• Fixed backup radio seamless channel change to non-DFS channel.
• Fixed link service uptime estimation.
• Fixed VRRP multicast traffic pass-through.
• Fixed Q-in-Q and PPPoE pass-through.
• Fixed an issue where Ethernet went down.
• Fixed MTU settings.
• Fixed an issue that caused multiple VLANs to go in both directions on bridge mode.
• Fixed initial frequency selection for Wave AI.
• Fixed GPS reporting.
• Fixed an issue with generating support files.
• Added various system settings, reporting and stability fixes.
• Added various UX fixes.

Additional information

• For proper statistics reporting, all endpoints of the link must be upgraded to 3.1.1-RC or to a more recent version.

Wave PTMP/PTP 3.1.6 includes the below change.

Bugfixes

• Fixed an issue where the Wave AP interface crashes.

Additional information

• For proper connection with the Wave AP Micro, all link endpoints must be upgraded to 3.1.5 or a more recent version.

Wave PTMP/PTP 3.1.5 includes the below changes.

Improvements

• Added support for Wave AP Micro.

Bugfixes

• Fixed various web interface, settings, and reporting issues.
• Fixed several stability issues.

Additional information

• For proper connection with the Wave AP Micro, all link endpoints must be upgraded to 3.1.5 or a more recent version.

New release for Wave PTMP product family (Wave AP, Wave Nano and Wave Long Range, AF60-LR)

Bugfixes

• Wireless: Backup radio: VLAN passthrough fix.
• Wireless: Backup radio: Wave AP high TX power setting fix.
• Network: Fix hostname inclusion in DHCP request packet.
• System: Fix statistics reporting when MTU in the link is inconsistent.
• System: Various settings, reporting and stability fixes.
• WEB UI: Various fixes.

Additional information

• If no direct access to Internet from device, please use UISP application or manual FW update.
• Statistics reporting between 3.1.1 (RC/RC2) and 3.1.0 (older FW versions too) is incompatible. To have proper statistics reporting, you must upgrade all PTMP network endpoints of the link to 3.1.1-RC or newer FW version.
• Old generation Wave AP (1 Eth. without backup radio)) and AF60-LR can't be downgraded from 3.1.1 to 3.0.2-beta5 FW version or AF60-LR can't be downgraded to 2.6.1 or older FW's.
• Direct upgrade from 3.0.2-beta5 to 3.1.1 is not possible, you need to upgrade to 3.1.0 FW first.